DTC Troubleshooting: P2564
DTC P2564: Turbocharger Wastegate Control Actuator Position Sensor Circuit Low Voltage
NOTE: Before you troubleshoot, review the general troubleshooting information.

DTC Description
Confirmed DTC
Pending DTC
P2564 Turbocharger Wastegate Control Actuator Position Sensor Circuit Low Voltage
    

1.
Problem verification:

Problem verification
?1.
Turn the vehicle to the ON mode.

?2.
Check the parameter(s) below with the HDS.
Signal
Threshold
Current conditions
Values
Unit
Values
Unit
EWG VOLTAGE FROM LIFT SENSOR
Less than 0.16
V
    

Do the current condition(s) match the threshold?

     
YES
     
     
     
Go to step 2.
     
NO
     
     
     
Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the turbocharger and the PCM. If the on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the on-board snapshot.?
2.
Determine possible failure area (DCWGL line, others):

Determine possible failure area (DCWGL line, others)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Turbocharger 5P connector

?3.
Turn the vehicle to the ON mode.

?4.
Check the parameter(s) below with the HDS.
Signal
Threshold
Current conditions
Values
Unit
Values
Unit
EWG VOLTAGE FROM LIFT SENSOR
Less than 0.16
V
    

Do the current condition(s) match the threshold?

     
YES
     
     
     
Go to step 5.
     
NO
     
     
     
Go to step 3.
3.
Determine possible failure area (turbocharger wastegate control actuator position sensor, others):

Determine possible failure area (turbocharger wastegate control actuator position sensor, others)
?1.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
 
Turbocharger 5P connector: disconnected
Test point 1
Turbocharger 5P connector (female terminals) No. 2:
Test point 2
Turbocharger 5P connector (female terminals) No. 3:


Is there about 5.0 V?

     
YES
     
     
     
     
NO
     
     
     
Go to step 4.
4.
Open wire check (VCC2 line):

Open wire check (VCC2 line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Jump the SCS line with the HDS, and wait more than 1 minute.


?3.
Disconnect the following connector.
PCM connector E (80P)

?4.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
 
Turbocharger 5P connector: disconnected
 
PCM connector E (80P): disconnected
Test point 1
Turbocharger 5P connector (female terminals) No. 2:
Test point 2
PCM connector E (80P) No. 77


Is there continuity?

     
YES
     
     
     
The VCC2 wire is OK. Check for any authorized service information related to the DTCs or symptoms you are troubleshooting, or substitute a known-good PCM.?
     
NO
     
     
     
Repair an open in the VCC2 wire between the PCM (E77) and the turbocharger.?
5.
Shorted wire check (DCWGL line):

Shorted wire check (DCWGL line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Jump the SCS line with the HDS, and wait more than 1 minute.


?3.
Disconnect the following connector.
PCM connector E (80P)

?4.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
 
Turbocharger 5P connector: disconnected
 
PCM connector E (80P): disconnected
Test point 1
Turbocharger 5P connector (female terminals) No. 4:
Test point 2
Body ground


Is there continuity?

     
YES
     
     
     
Repair a short in the DCWGL wire between the PCM (E60) and the turbocharger.?
     
NO
     
     
     
The DCWGL wire is OK. Check for any authorized service information related to the DTCs or symptoms you are troubleshooting, or substitute a known-good PCM.?