DTC Troubleshooting: C1041-00, C1042-00, C1043-00, C1044-00
DTC C1041-00: Right Front Wheel Abnormal Slip Detection
DTC C1042-00: Left Front Wheel Abnormal Slip Detection
DTC C1043-00: Right Rear Wheel Abnormal Slip Detection
DTC C1044-00: Left Rear Wheel Abnormal Slip Detection
NOTE: Before you troubleshoot, review the general troubleshooting information.

DTC Description
DTC
Freeze Frame
C1041-00 Right Front Wheel Abnormal Slip Detection
    
C1042-00 Left Front Wheel Abnormal Slip Detection
    
C1043-00 Right Rear Wheel Abnormal Slip Detection
    
C1044-00 Left Rear Wheel Abnormal Slip Detection
    

1.
Problem verification:

Problem verification
?1.
Turn the vehicle to the ON mode.

?2.
Clear the DTC with the HDS.


?3.
Turn the vehicle to the OFF (LOCK) mode, then start the engine.

?4.
Test-drive the vehicle at 12 mph (20 km/h) or more for at least 72 seconds.
NOTE: Drive the vehicle on the road, not on a lift.

?5.
Check for DTCs with the HDS.
DTC Description
DTC
Freeze Frame
C1041-00 Right Front Wheel Abnormal Slip Detection
    
C1042-00 Left Front Wheel Abnormal Slip Detection
    
C1043-00 Right Rear Wheel Abnormal Slip Detection
    
C1044-00 Left Rear Wheel Abnormal Slip Detection
    

Is DTC C1041-00, C1042-00, C1043-00, or C1044-00 indicated?

     
YES
     
     
     
The failure is duplicated. Go to step 2.
     
NO
     
     
     
Intermittent failure, the system is OK at this time. Refer to intermittent failures troubleshooting. If the freeze data/on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the freeze data/on-board snapshot.?
2.
Tire check:

Tire check
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Check all four tires for size, inflation, and wear.

Are all four tires the correct size, properly inflated, and worn evenly?

     
YES
     
     
     
Go to step 3.
     
NO
     
     
     
Swap the wheels and tires with a known-good set (the correct size, type, and properly inflated), then retest-drive the vehicle.?
3.
Wheel speed sensor performance check:

Wheel speed sensor performance check
?1.
Test-drive the vehicle at 12 mph (20 km/h) or more in a straight line.
NOTE: Drive the vehicle on the road, not on a lift.

?2.
Check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
RIGHT FRONT WHEEL SPEED
    
LEFT FRONT WHEEL SPEED
    
RIGHT REAR WHEEL SPEED
    
LEFT REAR WHEEL SPEED
    

Is any one of the four values different?

     
YES
     
     
     
Go to step 4.
     
NO
     
     
     
Check for loose terminals and poor connections in the VSA modulator-control unit 46P connector. Check for any authorized service information related to the DTCs or symptoms you are troubleshooting. If they are OK, replace the VSA modulator-control unit.?
4.
Wheel speed sensor check:

Wheel speed sensor check
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Substitute a known-good wheel speed sensor.

?3.
Turn the vehicle to the ON mode.

?4.
Clear the DTC with the HDS.


?5.
Turn the vehicle to the OFF (LOCK) mode, then start the engine.

?6.
Test-drive the vehicle at 12 mph (20 km/h) or more for at least 72 seconds.
NOTE: Drive the vehicle on the road, not on a lift.

?7.
Check for DTCs with the HDS.
DTC Description
DTC
Freeze Frame
C1041-00 Right Front Wheel Abnormal Slip Detection
    
C1042-00 Left Front Wheel Abnormal Slip Detection
    
C1043-00 Right Rear Wheel Abnormal Slip Detection
    
C1044-00 Left Rear Wheel Abnormal Slip Detection
    

Is DTC C1041-00, C1042-00, C1043-00, or C1044-00 indicated?

     
YES
     
     
     
Go to step 5.
     
NO
     
     
     
5.
Magnetic encoder check:

Magnetic encoder check
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Inspect the magnetic encoder for damage, debris, and correct installation.
Appropriate Magnetic Encoder
Note
Left-front
Remove the driveshaft outboard joint from the appropriate wheel hub.
Right-front
Left-rear
Remove the hub bearing unit.
Right-rear

Is the magnetic encoder surface OK?

     
YES
     
     
     
Check for loose terminals and poor connections in the VSA modulator-control unit 46P connector. Check for any authorized service information related to the DTCs or symptoms you are troubleshooting. If they are OK, replace the VSA modulator-control unit.?
     
NO
     
     
     
Clean the debris from the appropriate magnetic encoder surface on the wheel bearing or the hub bearing unit. If the debris cannot be removed or the encoder is damaged, replace the appropriate wheel bearing or the hub bearing unit.?